Spare Parts for Automatic Pool Cleaners, Page 2

Useful for the following types of Dolphin vacuum cleaners. Spring Galaxy D 2001 3001 Supreme M3 Supreme M4 Moby etc. No cable included Email us to confirm if this...

Including the screw, you simply unscrew the original and screw in the new propeller. Parameter Dimension Diameter 60 mm   Dolphin Galaxy...

For Zodiac Cyclonx - all versions. Belt included. DOES NOT INCLUDE WHEELS!!! The cassette can wear out over time and needs to be replaced.On the other side of the robot is a...

For Zodiac Cyclonx - all versions. The engine should be tested underwater after setup. If you test it out of the water, it will work for a few seconds due to its own special...

Manufacturer type Zodiac Cyclonx 4400 Zodiac Cyclonx 4401 Zodiac Cyclonx 4402 Zodiac Cyclonx 4380 Zodiac Cyclonx 4100 Original spare...

Compatible models Dolphin Moby Dolphin Galaxy Dolphin Spring Dolphin M3 Supreme Dolphin W20   Parameter Value Length...

For Zodiac Cyclonx - all versions. The cover may crack over time and must be replaced. Dimensions Value length 34 cm Width 26.5 cm

Backup drive belt for Dolphin S200 1pc (2pcs are needed per vacuum cleaner) Parameter Value Width 3.7 cm Circuit 95 cm

Replacement front PVC active brush for Dolphin S200 and S300i (1pc per vacuum cleaner is enough) Parameter Value Blue brush width 26.4 cm Total width...

Compatible models Dolphin Moby Dolphin Galaxy Dolphin Spring Dolphin M3 Supreme Dolphin W20   Parameter Value Width...

Spare drive belts for Dolphin D2001, D2002 Plus, Dolphin Dynamic, Dolphin Diagnostic 2pcs - Competitive set (2pcs per vacuum cleaner are needed) Parameter Value...

Spare transformer for Dolphin E20. The trafo does not include a cable - this must be purchased separately - Dolphin E trafo cable Output voltage 29V 180W IP protection:54

Complete set (2pcs) of wonder brush for vacuum cleaner Zodiac CyclonX 4100, Zodiac Cyclonx 4400 and Zodiac Cyclonx 4401, 4380. They are used when the robot cannot climb the...

Rubber cap - for brush - complete set is 2pcs, package contains 1pc. Dolphin D2001  

Pool robot shaft bearing, mounts on the hexagonal motor output and drives the belts. Dolphin Spring Dolphin Galaxy Dolphin D2001 Dolphin D2002 Dolphin...

Rear rear wheel.Part No. 11 Without screws.  Spare part as shown Parameter Value Wheel diameter 6.3 cm Thickness 3 cm

The finest filter to collect the finest dirt. The standard basket in the robot is 100mic. So this one has a smaller hole size.   Parameter Value width 24.5...

For Dolphin E20, including propeller. This motor is direct current (DC) so it is only compatible with DC power. The motor should be tested underwater after setup. If you try...

Coarse filter - insert for coarse dirt for S200, S300, S300IoT robots This insert is placed in the fine filter.    

For Dolphin Spring, including propeller. This motor is direct current (DC) so it is only compatible with DC power. The motor should be tested underwater after setup. If you...

Additional transformer for Zodiac Cyclonx  Output voltage 29V  

Pool Robot Brush Bearing. It is mounted on the belt and tube on which the brush is attached. Dolphin Spring Dolphin Galaxy Dolphin D2001 Dolphin D2002...

Original spare part for Dolphin D2001, D2002 plus 18 meter cable with connector on each side. If you are unsure, please contact our team.

For Dolphin E10, including propeller. This motor is direct current (DC) so it is only compatible with DC power. The motor should be tested underwater after setup. If you try...