Fix a Leak 235ml - sealing cracks in the pool

Product detailed description

Czech instruction manual for fix and leak

Special repair product for swimming pools and hot tubs since 1980

Useful for:

• Swimming pools
• Swimming tubs
• Home pools
• Lake pools
• Tanks

Important tips for using Fix and Leak

FIX A LEAK : is a mixed concentrate designed to repair leaks in virtually all materials - foil, concrete, shell, tiled pools and tubs.

Seals holes up to 3mm in diameter.
As a sealant it can be applied permanently.
235ml pack is usable up to 15m3.
If the leak has only been reduced but not completely removed, repeat the process again.

Warning - leaks in the suction pipe (from skimmer to filtration)
Leaks on the suction side are usually identified by leakage of aerated water from the return
pool jets. It is necessary to reverse the
direction of the flow to ensure that the leaking material is penetrated by the pressurized material.Under negative pressure, no fix and leak will settle at the leak location!
VERY IMPORTANT: After the leak in the suction line has been repaired, it is absolutely necessary to separate
the suction branch from the repaired line for at least 72 hours. This is the amount of time that
FIX-A-LEAK needs to properly mature and cure.
Miscellaneous leaks:
If you suspect that water is leaking through individual elements inside the pool (lights, stairs, jets, bottom) then:
Stop the pump. Apply FIX-A-LEAK directly to the leak using a squeezeable elastic bottle (similar to ketchup).
Allow the product to cure for a minimum of 48 hours before restoring circulation.

NOTE: FIX-A-LEAK is perfectly tested. Directly in the field and in a wide variety of
weather conditions, it has proven to be effective in repairing leaks.
FIX-A-LEAK has also demonstrated excellent preventive maintenance properties by forming a coating on
the relevant surfaces, which then protects them from corrosion.

HOW TO USE FIX A LEAK

* Shake thoroughly before use*

If cold or unable to shake, place the entire bottle in warm water for a few minutes
1. Before adding FIX-A-LEAK to the water, secure the FILTER-SAND FILTRATION bypass (set the circulation to the pool at the six-way valve). If the fix-a-leak gets into the sand, glass or zeolite, it will seal it!!!
Alternatively, you can remove the sand, glass or zeolite from the container.
2. Turn on the pump and slowly add FIX-A-LEAK with a skimmer, or
pour into the pool at the affected areas you have identified.
3. After adding FIX-A-LEAK, adjust the suction to the main outlet. If this is not possible, an alternative
is to use a suction pump, which you place in the deepest part of the pool and allow it to suck normally. However, leave circulation to the pool at the valve.
4. FIX-A-LEAK is very heavy and as such will drop to its lowest point quite quickly. Therefore
it should always be stirred after 4-6 hours while the water is circulating to soften it. This is done either manually with a pool brush or mechanically using an automatic
dryer that you throw into the pool without a basket!!!
5. Recirculate the water until the leak stops.
6. Mark the water level in the pool with a line and check after 2-3 days to see if the water is no longer leaking.
7. Even if you find that the water is no longer leaking, allow the product to work for another 24-48 hours
to properly cure. This process takes 72 hours - 1 day of circulation, 2 days of standing.
Then resume normal filtration.
8. Repeat the process as needed.

After three days, the residue of fix and lake can be sucked out into the sand, and the sand can then be properte.
If you see deposits on the skeleton, drain the water and with a dampened cloth, remove all residue
of the agent from the surface. Refill the bath after three days.

CAUTION: Keep out of reach of children.
The agent is a severe eye and skin irritant. Do not allow it to come into contact with eyes,
skin or clothing. It is harmful or fatal if swallowed. Avoid contamination of food. Empty containers should be rinsed thoroughly with water before disposal.
FIRST AID: In case of eye or skin contamination, immediately apply running water to the affected area. Do not spare it and rinse for at least fifteen minutes. If the eye is involved,
seek medical attention. Remove contaminated clothing and wash before reuse. If swallowed, drink milk, egg white, gelatine solution. If these are not available, drink plenty of water. Seek medical attention immediately.